The Ghost Box

The Art of Pranking Part II

The bigger, badder wireless pranking device that evolved from Part I of our pranking bonanza. This is a somewhat technical post. A following post will detail our exploits with it.

The completed device

Learning from the Past

There were a few issues with the first model.

1. The photocell was clearly visible on the front of the adapter and that made it look suspicious.


2. High maintenance. The contraption didn't work well when it was dark outside. In the interest of simplicity, it was designed to sound when it got too dark. That is, in the normal case, when a shadow fell across it. How dark was too dark was adjustible with a screwdriver. Of course, that meant that Ryan had to turn it off each night or if it rained out. This also made it high maintenance, because it didn't turn off automatically - it would keep sounding as long as the target was casting a shadow over the photocell. This drove Ryan crazy, since he had to listen to it and turn it on and off all the time.


3. It was not wireless. Fazeel was eventually able to follow the cord back to the noise box when he figured it out. Then the jig was up.


4. It only emitted one single type of noise. Although deliciously annoying, it didn't offer as much flexibility as we'd like.

Solutions

1. The photocell should be better concealed. Bought a Nortel adapter at Skycraft Surplus for $5 apiece. Using a cordless saw, opened it up, removed the internals. Cut the transformer from the prongs that go into the wall socket, leaving enough plastic around them to keep them solid, and taped the terminals up to insulate them thoroughly from each other and the rest of the electronics I was stuffing in the box. Took one of the detectors from the toy (see below), pulled out the electronics and put them in.
   
   
   Cut off the antenna and hooked up the adapter's cord as the new antenna. Added a battery holder and two AAA batteries. Drilled out a hole for the sensor, slipped it through. Still pretty conspicuous.
   
   
   
   
   To obscure the photocell, cut clear contact paper into a rounded-rectangle shape consistent with the types of stickers you might find on these things. Then, colored over the contact paper with black dry erase marker.
   
   
   
   Because this adapter now has batteries (the adapter from the previous prank didn't since it was powered from the box it was attached to), I had to install some sort of switch to keep the batteries alive. Otherwise, I'd have to tear that thing back open all the time to replace them. I really didn't have a way to solidly mount a tiny switch, so I slipped a tiny reed (magnetic) switch in the seam. It's powered on by sticking a really tiny rare-earth magnet on the switch.


2. The device should roughly detect motion, specifically a rapid change in light intensity as opposed to merely detecting dark. This was nailed with the solution to the wireless problem described next.


3. Wireless would be ideal. This appeared to be beyond my skills and/or experience in electronics, but I found a toy at Toys 'R' Us that, appropriately modified, was wireless and sensed motion. It's called a SpyGear Wireless Tracker. This also had some issues when used in this way. For example, when triggered, it had a blinking red light (LED) that continued to blink until manually reset. That made my job with the glue circuitry a lot more complex.
   
   


4. Plays back a recorded message. This appeared to be the easiest to accomplish. Radio Shack, in fact, sells a voice recording/playback module for about $10 (above). This device was almost perfect. The difficult thing about it was that it had a rubber plunger switch to playback with no leads or any apparent way to hook into and trigger it from other circuitry. So I had to take the switch apart, drill tiny holes in the PCB for the wires and solder them directly onto the traces underneath. Not ideal. Sound quality is not great, but then I didn't really expect that much.

Finishing Up

The receiver mess (with voice record/playback unit) in nearly completed form.

Getting the glue circuitry working correctly was a pain, in the end I went for an inefficient but dead simple approach that made all the pieces work together. Maybe in the future I'll refine it. Anyhow, for now, I'm pretty happy with it.

More to come on the fun we've had.. !